Research Journal of Chemical Sciences ______________________________________________ ISSN 2231-606X Vol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 32 Equilibrium and Thermodynamic Studies on Adsorption of Cd2+ and Zn2+using Brachystegia eurycoma Seed coat as BiosorbentOnwu F.K* and Ngele S.O.Department of Chemistry, Michael Okpara University of Agriculture Umudike, P.M.B 7267, Umuahia, Abia State, NIGERIA Department of Industrial Chemistry, Ebonyi State University, P.M.B. 053 Abakaliki, NIGERIAAvailable online at: www.isca.in, www.isca.me Received 12th January 2015, revised 31st January 2015, accepted 14th February 2015 AbstractThe potential of B.eurycoma seed coat as biosorbent for removing Cd2+ and Zn2+ from aqueous solutions has been studied. Batch adsorption experiments were carried out as function of pH, initial metal ion concentration and temperature. Maximum metal sorption was found to occur at pH 6.0 at initial concentration of 30 mg/L and at 30C. The maximum adsorption capacity of B.eurycoma corresponding to sites saturation was found to be 4.286 and 4.390 mg/g respectively for initial Cd2+and Zn2+ concentration of 30 mg/L at a temperature of 40 C. The results were analyzed by the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich (D–R) isotherms using linearized correlation coefficient at different temperatures. Results showed that the Langmuir and Freundlich models gave the best interpretation to the equilibrium adsorption data for the Cd(II) and Zn(II) ions–B.eurycoma systems studied. The following thermodynamic parameters: H, S and G were calculated and results obtained showed that the adsorption process was exothermic and spontaneous. Keywords: Adsorption, B.eurycoma, biosorbent, isotherms, biosorption. Introduction Environmental pollution with heavy metals has become a colossal issue as a result of industrial and metallurgical processes which release a great number of toxic chemicals into the environment1,2. The heavy metals of widespread concern to human health are lead, copper, mercury, cadmium, arsenic, chromium and zinc3-5. Toxic heavy metals are considered as major pollutants that have direct effects on man and animals and their concentrations in our environment have reached alarming levels in terms of their effects on living organisms. Zn2+ which is considered an essential element for life and a micronutrient in trace amounts is a common metal ion found in effluents of a large number of industries. However, continual exposure to Zn2+is detrimental to human health. The toxicological effects of Zn2+ have been documented in the chemical literature and its presence in water and wastewaters is a potential risk for the environment and public health5,7,8. Cadmium is also a toxin even in relatively low dosages and is one of the major heavy metals that cause kidney damage, renal disorder, high blood pressure, bone fraction and destruction of red blood cells. Cadmium(II) has also been implicated as a potential carcinogen10-12. Therefore, it is necessary to design feasible processes to minimize the pollution caused by Zn(II)and Cd(II) discharges and to reduce the risks associated with their presence in the environment. The task of providing proper treatment facility for heavy metal pollutants is difficult and some of the techniques are either expensive or inefficient, hence there is pressing demand for innovative technologies which are low cost, require low maintenance and are energy efficient. The adsorption technique is economically favourable and technically easy to separate as the requirement of the control system is minimum. Instead of using commercial activated carbon, researchers have worked on inexpensive materials, such as Tea waste13, Cassava wastes14, modified rice husk, Fluted pumkin15, waste acorn of Quercus ithaburensis16, Oil palm fruit fibre17, African Star apple shell18and other adsorbents, which have high adsorption capacity and are locally available. In this article, the technical feasibility of low-cost adsorbent from agricultural waste for heavy metal removal from aqueous solutions has been investigated. B. eurycoma whose seed coat is employed as biosorbent in the present study is a plant that grows mainly along the river banks or swamps in Western and Eastern Nigeria. It is a large tree with irregular and twisted spreading branches. The seed has a roundish flat shape with brown colour and hard hull. In Nigeria, the main culinary use of the gum from B. eurycoma seedis in thickening soups. Thickeners are usually added as condiments in the preparation of most soups. They are known to cause increased viscosity in soups, giving it more palatability and good mouth feel. The seed coats are discarded and are considered wastes. Assessment of the Phytochemical contents of the seeds of B. eurycoma shows that the seeds contain Alkaloids (1.74%), Flavonoids (3.72 %), Tannins (0.70%), Saponins (0.87%) and Phenols (0.03%)19. Flavonoids are a group of polyphenolic compounds that are found in fruits and vegetables. These metabolites posses some functional groups and their presence in the seeds indicates that they could have potential to bind metal ions from aqueous solutions. Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 33 Material and Methods Preparation of the adsorbents: The seeds of Brachystegia eurycoma were purchased from Abakaliki meat market, Ebonyi State. They were soaked in water until they became turgid. Their coats were removed, washed extensively in running tap water to remove dirts and other particulate matter and then sun-dried. They were later oven-dried for 2 h at a temperature of 50 C. The dried samples were crushed using grinding mill fitted with sieves to obtain a particle size of 250 µm. The samples were stored in tight plastic containers and kept for the adsorption analysis. 100 g of the screened sample was soaked in excess of 0.3 M HNO3 solution in a beaker, stirred for 30 min at a temperature of 30 C and then left undisturbed for 24 h. They were then filtered through a whatman filter paper and rinsed severally with deionised water until a pH 7 was obtained. The adsorbents were finally air-dried. The treatment with acid opens up the pores of the adsorbent samples in preparation for the adsorption analysis and to destroy any debris or soluble biomolecules that might interfere with the metal ions during the adsorption process. Adsorbates Preparation: Stock solutions of 1000 mg/L of each of the metal ions, cadmium and zinc were prepared from their salts, CdSO.8HO, and ZnSO.7HO respectively. From the stock solutions, different working concentrations ranging from 5 - 30 mg L-1 of each of the metal ions were prepared by serial dilution. The effect of concentration on the adsorption of the metal ions was studied by transferring 25 mL of the different concentrations of the metal ions into different 250 mL conical flasks while maintaining the pH of the solutions at 6.0 and at temperature 30C. Thereafter, 0.2 g of the biosorbent was weighed into the flasks, corked and labeled and agitated in a rotary shaker for 1 h. At the end of the adsorption process, the content of each flask was filtered, centrifuged and the residual metal ion concentrations (C) analyzed. The process was also repeated at temperatures of 40 and 50 C. The concentrations of the standards and the test solutions were confirmed using buck scientific Atomic Absorption Spectrophotometer (AAS) model 205. The pH of the adsorbate solutions was maintained at 6.0. For the study on influence of pH on the adsorption process, a similar procedure was carried out just as in the case of initial metal concentration except that a fixed initial metal ion concentrations of 30 mg/L was used and the pH of the solutions adjusted from pH 2 to 8 using either 0.1 M HCl or 0.1 M NaOH solution and at a fixed temperature of 30C. The amount of the metal ions adsorbed was calculated by difference. The analysis was carried out in triplicates and mean residual concentrations analyzed. The amount of metal ions adsorbed at equilibrium, q(mg/g) was determined using the mass balance equation (1). V m CCqee´ - (1) Where and are the initial and equilibrium concentrations (mg/L), V is the volume of solution (L) and m the dry weight of the biosorbent (g). Results and Discussion Effect of pH: The amounts of zinc and cadmium ions adsorbed onto the adsorbent at the various pH values are shown in figure-1. The pH of an aqueous solution is an important parameter affecting both the amount of metal ions furnished in aqueous solution as well as the number of binding sites on the adsorbent20. The sorption capacity of the biosorbent increased with increase in pH of the solution and maximum pH value for adsorption of Cd2+ and Zn2+ by B. eurocoma was observed at pH 6.0 with adsorption capacities of 2.713 mg/g for Cd2+ and 2.936 mg/g for Zn2+ at a temperature of 30C and initial concentration of 30 mg/L. The decreased sorption capacity at low pH values 5, may have resulted from the protonation of the ligands at the surface of the B. eurocoma. The generation of hydroxonium ions [H] in the bulk solution at low pH could result in competition between the hydroxonium ions and the metal ions for active sites and such a competition may have caused a decrease in the amount of metal ions adsorbed. But as the pH is increased, the hydroxonium ions are gradually dissociated and the positively charged Zn(II) and Cd(II) ions could bind with the free binding sites of B. eurocoma leading to an enhanced removal of the metal ions. Similar findings have been reported by other researchers20,21. The adsorbent generally showed a preferred affinity for Zn2+ than Cd2+ at the initial concentration of 30 mg L-1 employed. Effect of metal ion concentration: In this study, the effect of initial Cd2+ and Zn2+ concentration on sorption onto the B.eurycoma was investigated in the range of 5–30 mg/L and the equilibrium uptake capacities (mg/g) at 30, 40, 50C are presented in f igures-2 and 3 . The f igures show the variation of the equilibrium adsorption capacity of the B.eurycoma with initial Cd2+ and Zn2+ concentration and temperature. It was observed that the amount adsorbed, q (mg/g) increased with both increasing initial metal ion concentrations and increasing temperature under studied ranges. The maximum equilibrium adsorption capacity values were determined as 2.713, 2.885 and 2.824 mg/g for 30 mg/L initial Cd2+ concentration at 30, 40 and 50 C, respectively and 2.936, 3.170 and 3.094 mg/g for Zn2+ for the same initial concentration and temperature ranges. The enhancement in the adsorption capacity may be due to the chemical interaction between adsorbates and adsorbent sites or the increased rate of intraparticle diffusion of Cd2+ and Zn2+ into the pores of the adsorbent at higher temperatures22. Results also showed that Zn2+ was better adsorbed than Cd2+. Adsorption Isotherms: A clear equilibrium distribution of the metal ions between the adsorbent (B.eurycoma) and liquid (bulk solution) phases is represented by adsorption isotherms. An adsorption isotherm is characterized by certain constant values, which express the surface properties and affinity of the Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 34 adsorbent and can also be used to compare the adsorptive capacities of the adsorbent for the different metal ions23. In order to determine the mechanism of Cd2+ and Zn2+ adsorption onto the adsorbent, the experimental data were applied to the following two-parameter isotherms: Langmuir, Freundlich, Dubinin-Radushkevich (D–R) and Temkin equations. The constant parameters of the isotherm equations for the adsorption process were calculated by regression using linear forms of the isotherm equations. The Langmuir Isotherm model: The Langmuir isotherm is valid for monolayer adsorption onto a surface containing a finite number of identical sites. The model assumes uniform energies of adsorption onto the surface and no interaction among adsorbed species occurs. Based upon these assumptions, the linearized Langmuir equation is represented as24: 00 1 ee eL CC qQKQ =+ (2) Where: C = the equilibrium concentrations of Cd2+ and Zn2+(mg/L), q = the amount of metal adsorbed per gram of the adsorbent at equilibrium (mg/g), Q = maximum adsorption capacity corresponding to sites saturation (mg/g) and K = Langmuir isotherm constant (L/mg). The Langmuir parameters, and K are computed from the slope and intercept of the Langmuir plots. Figure-1 Effect of pH on the adsorption of Cd2+ and Zn2+ by B.eurycoma at 30 C and initial conc. 30 mg/L Figure-2 Effect of initial metal ion concentration on the amount of Cd2+ adsorbed at different temperatures Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 35 Figure-3 Effect of initial metal ion concentration on the amount of Zn2+ adsorbed at different temperaturesTable-1A Langmuir Isotherm Constants for adsorption of Cd(II) and Ni(II) ions by the adsorbent at different temperatures Parameters Cd 2+ Zn 2+ Temperatures 30 0 C 40 0 C 50 0 C 30 0 C 40 0 C 50 0 C K L (L/mg) 0.2513 0.3627 0.2800 0.3985 0.6022 0.4759 Q 0 (mg/g) 4.0177 4.2863 4.1445 4.1102 4.3898 4.3592 L at 30 mg/L 0.1171 0.0842 0.1064 0.0772 0.0525 0.0655 R 2 0.9378 0.9833 0.9735 0.9943 0.9864 0.9933 The essential features of the Langmuir isotherm are also expressed in terms of equilibrium parameter R, which is a dimensionless constant referred to as separation factor or equilibrium parameter25. 1 (1) L Lo R KC (3) Where: C = initial metal ion concentration, K = the constant related to the energy of adsorption (Langmuir Constant). Rvalue indicates the nature of adsorption to be either favourable if 0 R1, linear if R =1, unfavourable if R.64;ᤠ1 and irreversible if R=0. From the data presented in table-1A, the R is greater than 0 but less than 1 indicating that Langmuir isotherm is favourable. The Rvalues .64;ᤠ 0.9300 show that the sorption data fitted well into Langmuir Isotherm model. The calculated Langmuir parameters, Q, K and R and the Rvalues are summarized in table-1A. Equilibrium Freundlich Isotherm: The Freundlich model is derived to model the multilayer adsorption, applicable to a highly heterogeneous surface and is represented as24: 1 lnlnln eFe qkC n =+ (4) where K represents maximum adsorption capacity and n is related to the adsorption intensity and both constants are calculated from the intercept and slope of linear plots of ln q vs ln C according to equation-4. The equilibrium Temkin isotherm: TheTemkin isotherm describes thecharacteristic adsorption potential of the biosorbent for the metal ions. The derivation of the Temkin isotherm assumes that the fall in the heat of adsorption is linear rather than logarithmic, as implied in the Freundlich equation16. The linearized form of the isotherm model is given as: lnln eTe TTRTRT qkC bb=+ (5) Where (mg/g) and (mg/L) are the amount adsorbed at equilibrium and the equilibrium concentration, respectively. Tthe absolute temperature in Kand Ris the universal gas constant, 8.314 J mol 1 K 1. Dubinin-Radushkevich Isotherm: The Dubinin-Radushkevich (D-R) model was applied to the equilibrium data to assess the nature of the adsorption process, i.e. whether it is physical or chemical adsorption. The linearized D-R adsorption isotherm is represented as16: Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 36 (6) (7) Where qD is the theoretical saturation value (mg/g), q is the amount adsorbed at equilibrium (mg/g), B is a constant related to adsorption energy (mol kJ-2), R is the gas constant (8.3145 J mol-1 K-1), T is the temperature (K) and is the Polanyi potential which is related to the equilibrium concentration as expressed in equation (7). The constant B gives an idea of the mean energy, E (kJ mol-1) of adsorption per mole of the adsorbate as it is transferred to the surface of the solid from infinite distance in the solution and this energy is usually evaluated from the relation in equation-8. (8) It can be observed from figures 4–9 and tables-1A-C, that the adsorption of Cd2+ and Zn2+ onto B.eurycoma at the range of temperatures 30-50C fits quite well into the Langmuir, Freundlich and Temkin adsorption models with Langmuir and Freundlich showing best descriptions for the adsorption data. From table-1D, it was also observed that the experimental data obtained showed lower fitting into the Dubinin-Radushkevich (D-R) model. As seen from figures-4-11, the isotherms of Cd2+and Zn2+ adsorption on B.eurycoma were found to be linear over the whole temperature range studied and the correlation coefficients were extremely high as shown in Tables 1A-D. The values of K and Q obtained from Langmuir plots increase with temperature increase showing optimum at 40C and decreases afterwards. The value of Kdetermined from the Freundlich model changed with the rise in temperature giving maximum values at 40C. The magnitude of Kshowed high Cd2+ and Zn2+ adsorptive capacity of the B.eurycoma from aqueous solutions at all temperatures. Table 1B also indicated that nwas greater than 1.0 at all temperatures, indicating that Cd2+ and Zn2+ were favourably adsorbed by the B.eurycoma. From table-1D, it can be observed that the obtained values of mean D-R energy, are within the range of 1.060 -1.578 kJ mol-1, indicating that physisorption may have played a dominant role in the adsorption of Cd2+ and Zn2+ onto the biosorbent. The constant obtained for Temkin isotherms are shown in table-1C. The Temkin isotherm constant in Table 1C shows that the heat of adsorption () increases with increase in temperature. The change in enthalpy (H) and entropy (S) of the adsorption process was calculated from the variations of the Langmuir constant, K with change in temperature using the following relation: ln GS K RTRTR D-DHD =-=+The Gibb’s free energy at 303K was evaluated using the relation: GHTS D=D-D (9) Where R is the gas constant (8.314 J mol 1 K 1) and T is the temperature (). A plot of ln K versus 1/T yields straight line as shown in figure-12, from which and were calculated from the slope and intercept, respectively. Thermodynamic assessment of the adsorption data (table-2) showed that the G D values were all negative. The negative G D values indicate the feasibility and spontaneous nature of the adsorption process. The G D values obtained in this study for the metal ions were all less than –10 kJ/mol, suggesting that physical adsorption is the predominant mechanism in the sorption process and confirms the exothermic nature of the adsorption process. The positive values of S D may reflect the affinity of the B.eurycoma for the metal ions and also suggest some structural changes in the metal ions and adsorbent system, and that the freedom of the metal ions is not too restricted on the surfaces. Figure- 4Langmuir isotherm plots for adsorption of Cd2+ onto B.Eurycoma at different temperatures Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 37 Figure-5 Langmuir isotherm plots for adsorption of Zn2+ onto B.eurycoma at different temperatures Figure-6Freundlich isotherm plot of ln q vs ln C for adsorption of Cd2+ onto B.eurycoma at different temperatures Figure-7 Freundlich isotherm plot of ln q vs ln C for adsorption of Zn2+ onto B.eurycoma at different temperatures Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 38 Figure-8 Temkin isotherm plot of q vs ln C for adsorption of Cd2+ onto B.eurycoma at different temperatures. Figure-9 Temkin isotherm plot of q vs ln Ce for adsorption of Zn2+ onto B.eurycoma at different temperatures Figure-10 Dubinin-Radushkevich isotherm plot of ln qe vs for adsorption of Cd2+ onto B.eurycoma at different temperatures Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 39 Figure-11 Dubinin-Radushkevich isotherm plot of ln qe vs for adsorption of Zn2+ onto B.eurycoma at different temperatures Table-1B Freundlich Isotherm Constants for adsorption of Cd(II) and Zn(II) ions by the adsorbent at different temperatures Parameters Cd 2+ Zn 2+ Temperatures 30 0 C 40 0 C 50 0 C 30 0 C 40 0 C 50 0 C 1.0175 1.2209 1.0961 1.1911 1.5700 1.3515 n 2.1459 1.9631 2.0433 1.8904 1.5142 1.7848 R 2 0.9802 0.9881 0.9798 0.9898 0.9914 0.9830 Table-1C Temkin Isotherm Constants at different temperaturesParameters Cd 2+ Zn 2+ Temperatures 30 0 C 40 0 C 50 0 C 30 0 C 40 0 C 50 0 C 1.9727 3.0053 2.0292 3.2943 3.9001 3.8991 (kJ/mol) 2.583 2.474 2.355 2.583 2.190 2.423 R 2 0.9418 0.9764 0.9643 0.9888 0.9502 0.9907 Table-1D Dubinin-Radushkevich Isotherm Constants for adsorption of Cd(II) and Zn(II) ions at different temperatures Parameters Cd 2+ Zn 2+ Temperatures 30 0 C 40 0 C 50 0 C 30 0 C 40 0 C 50 0 C (mg g - 1 ) 2.432 2.742 2.681 2.742 3.174 2.983 (mol 2 kJ - 2 ) X 10 - 7 4.279 2.968 4.453 2.881 2.008 2.407 E (kJ mol - 1 ) 1.081 1.298 1.060 1.317 1.578 1.441 R 2 0.8379 0.9029 0.9260 0.9250 0.9849 0.9653 Table-2 Thermodynamic parameters for the adsorption processMetal ions Parameter ( ) / HkJmol D ( ) 11 SJmolK-- ( ) / GkJmol D Cd 2+ -7.394 2.163 -6.739 Zn 2+ -7.689 0.446 -7.554 Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 40 Figure-12 Plot of ln K vs 1/T for estimation of the thermodynamic parameters ConclusionThe present study evaluates the efficiency of B.eurycoma seed coat in removing Cd2+ and Zn2+ from aqueous solutions. Based on the findings of the present study and information obtained from Chemical literature, the following conclusions can be drawn: B.eurycoma is capable of removing Cd2+ and Zn2+ from aqueous solutions. The batch adsorption studies were dependent on pH, initial metal ion concentration and temperature. The optimum pH for removal of Cadmium and Zinc by B.eurycoma occurred at a pH 6.0. Langmuir, Freundlich, Dubinin-Radushkevich (D-R) and Temkin isotherm models were applied to the experimental adsorption data. Langmuir and Freundlich models provided the best description to the adsorption data at all the temperatures studied based on their high correlation coefficients. The energy values obtained from Dubinin-Radushkevich model were all less than 8.00 kJ mol-1 suggesting that physisorption may have been the predominant mode of the adsorption process. The obtained results are indication that the seed coat of B.Eurycoma could be applied as biosorbent for heavy metal removal from aqueous solutions and could be employed as an effective alternative method for the economic treatment of wastewater. References 1.Nazris N., Rahmiana Z., Edison M. and Jiye J., Biosorption of Copper (II), Lead (II), Cadmium (II) and Zinc (II) ions from aqueous solution by Nypa fruticansShell on batch method. J. Chem. Pharm. Res., 6(12), 370-376 (2014)2.Onwu F.K., Abii T.A. and Ogbonna A.C., Kinetic studies on the use of agricultural wastes for the removal of lead, cadmium and nickel ions from aqueous solutions, J. Chem. Pharm. Res., 6(12), 471-480 (2014) 3.Cordero B., Lodeiro P., Herrero R. and Sastre de Vicente M.E., Biosorption of Cadmium by Fucus spiralis, Environ. Chem. 1, 180-187 (2004)4.Crini G., Recent development of Polysaccharide-based materials used as adsorbent in waste water treatment, Progress in Polym. Sci., 30, 38-70 (2005)5.Igwe J.C. and Abia A.A., A bioseparation process for removing heavy metals from waste water using biosorbents. African Journal of Biotechnol., 5(12),1167-1179 (2006)6.Dada A.O., Olalekan A.P., Olatunya A.M. and Dada O., Langmuir, Freundlich, Temkin and Dubinin–Radushkevich Isotherms Studies of Equilibrium Sorption of Zn2+ Unto Phosphoric Acid Modified Rice Husk, IOSR Journal of Applied Chem., 3(1), 38-45 (2012)7.Volesky B., Detoxification of metal-bearing effluents: biosorption for the next century, Hydrometallurgy,59, 203–216 (2001)8.Bhattacharya A.K., Mandal S.N. and Das S.K., Adsorption of Zn(II) from aqueous solution by using different adsorbents, Journal Chem. Eng., 123, 43–51 (2006) 9.Krishnan K.A. and Anirudhan T.S., Removal of Cadmium(II) from aqueous solutions by steam-activated sulphurised carbon prepared from sugar-cane bagasse Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 5(2), 32-41, February (2015) Res. J. Chem. Sci. International Science Congress Association 41 pith : Kinetics and Equilibrium Studies, Water SA, 29(2), 147-156 (2003)10.Filipic M., Molecular mechanisms of cadmium induced mutagenicity, Human Exp. Toxicol., 25, 67-77 (2006)11.Akesson A., Julin B. and Wolk A., Long-term dietary cadmium intake and postmenopausal endometrial cancer incidence: a population-based prospective cohort study, Cancer Res., 68, 6435-6441 (2008)12.Kumar R., Abraham T.N and Jain S.K., The removal of cadmium ions from aqueous solutions using silica support immobilized with 2-hydroxyacetonephenone-3-thiosemicarbazone, nd International Conference on Environmental Science and Development, 4, 48-52 (2011)13.Manoj K.G., Sarita S., Ashok K.S. and Sanjay V., Study on removal of arsenic from aqueous solutions by low cost adsorbent, International Journal of Chem. Stud., 2(3), 30-35 (2014)14.Horsfall M. Jnr. and Spiff A.I., Equilibrium Sorption Study of Al3+, Co2+ and Ag in Aqueous Solutions by Fluted Pumpkin (TelfairiaOccidentalis HOOK f) Waste Biomass, Acta Chim. Slov.,52, 174-181 (2005)15.Malkoc E. and Nuhoglu Y., Determination of kinetic and equilibrium parameters of the batch adsorption of Cr(VI) onto waste acorn of Quercus ithaburensis, Chem. Eng. Proces.,46, 1020-1029 (2007)16.Abia A.A. and Asuquo E.D., Sorption of Pb(II) and Cd(II) ions onto chemically unmodified and modified iol palm fruit fibre adsorbent: Analysis of pseudo second order kinetic models, Indian Journal of Chem.Technol., 15, 341-348 (2008)17.Onwu, F.K. and Ogah S.P.I., Studies on the effect of pH on the sorption of cadmium(II), Nickel(II), lead(II) and chromium(VI) from aqueous solutions by African white star apple (Chrysophyllum albidium) shell. African Journal of Biotechnol., 9(42),7086-7093 (2010)18.Igwe O.U. and Okwu D.E., Phytochemical composition and anti-inflammatory activities of Brachystegiaeurycoma seeds and stem bark, Der Pharma Chemica, 5(1), 224-228 (2013)19.Ogbonna A.C., Abii T.A. and Onwu F.K., Equilibrium studies on biosorption of lead, cadmium and nickel ions using cassava waste biomass, J. Chem. Pharm. Res,6(12), 418-432 (2014)20.Farghali A.A, Bahgat M., Allah A.E. and Khedr M.H., Adsorption of Pb(II) ions from aqueous solutions using copper oxide nanostructures, Journal of Basic and Applied Sci., , 261-71 (2013)21.Karthikeyan T.S., Rajgopal L.R., Miranda, Chromium(VI) adsorption from aqueous solution by Hevea Brasilinesis sawdust activated carbon, J. Hazard. Mater., B124, 192–199 (2005)22.Dursun G., Çiçek H. and Dursun A.Y., Adsorption of phenol from aqueous solution by using carbonised beet pulp, J. Hazard. Mater., B125, 175–182 23.Anusiem A.C.I., Onwu F.K and Ogah S.P.I., Adsorption Isotherm Studies of Ni(ll), Cd (ll) and Pb (ll) ions from Aqueous Solutions by African White Star Apple Chrysophyllum albidium) Shell, International Journal of Chem., 20(4), 265-274 (2005)24.Chengwen S., Shuaihua W., Murong C., Ping T., Mihua S. and Guangrui G., Adsorption Studies of Coconut Shell Carbons Prepared by KOH Activation for Removal of Lead(II) From Aqueous Solutions, Sustainability, 6, 86-98 (2014)